Issue
The communication device LEDs are blinking in a pattern.
Cause
The Communication Device cannot communicate with the data server.
Resolution
When there is a problem, the device's LED lights near the network jack will flash in a pattern. The following list provides the meaning of each pattern, and the resolution for each situation.
Important: Many of these errors are related to network setup and connectivity issues. Contact your IT department for assistance when needed.
Flashing GREEN = Connection working (normal, no error)
The franking machine has a functioning network connection. No action is needed.
C02: ORANGE, GREEN, ORANGE, GREEN, [pause] = Auto IP Address not assigned
- Enable DHCP on the network or manually configure the network settings using the Network Setup Software.
- Power cycle the device:
- Unplug the device from power.
- Wait 10 seconds.
- Reconnect to power. This will update the firmware and reboot the communication device.
C03: ORANGE, GREEN, ORANGE, ORANGE, GREEN, [pause] = Communication device did not find the DNS server
- If the network is set up to use DHCP, reboot the device.
- If the network does not have DHCP:
- Disconnect the USB/network cable from the franking machine.
- Download and run the Network Setup Software to verify and manually configure the DNS.
- In addition to the DNS, you will need to specify the IP Address and Subnet mask.
- If the settings fail to update, reset the device to the factory defaults.
C04: ORANGE, GREEN, [pause] = franking machine does not have the right firmware to communicate with the communication device.
- Connect to the Pitney Bowes Data Centre, (perform a balance enquiry) to check for, download and install any updates.
- Power cycle the device:
- Unplug the device from power.
- Wait 10 seconds.
- Reconnect to power. This will update the firmware and reboot the communication device.
C05: ORANGE, ORANGE, ORANGE, GREEN, ORANGE, [pause] = Franking machine is not communicating with the communication device
- Wait 60 seconds. The error may clear on its own.
- If the error does not clear:
- Unplug the device from power.
- Wait 10 seconds.
- Reconnect to power. This will update the firmware and reboot the communication device.
- Replace the USB cable. Make sure that the new USB cable is no longer than 2.43 metres.
C06: ORANGE, ORANGE, GREEN, [pause] = Wireless network configuration may be incorrect
- Disconnect the USB cable from the franking machine.
- Run the Network Setup Software to confirm the correct wireless network was selected and that the wireless key was entered correctly.
- If the settings fail to update, reset the device to the factory defaults.
- After making changes, power cycle the device by disconnecting the power, waiting 10 seconds, and reconnecting the power.
C07: ORANGE, ORANGE, GREEN, ORANGE, [pause] = There is problem transferring data to the franking machine
- Wait 60 seconds. If the error does not clear, disconnect the power, wait 10 seconds, and reconnect the power.
- Replace the USB cable. Make sure that the new USB cable is no longer than 2.43 metres.
C08: ORANGE, ORANGE, ORANGE, GREEN, [pause] = Communication Device does not detect a network connection
- Check that the network cable is connected properly.
- Check that the network port to which the cable is connected is active.
- If adjustments are made, disconnect the USB cable and power cycle the communication device by disconnecting the power, waiting 10 seconds, and reconnecting the power.
C09: ORANGE, GREEN, ORANGE, [pause] = Network gateway address is not entered
- Enable DHCP on your network.
- Disconnect the USB cable from the franking machine.
- Download and run the Network Setup Software to verify and manually configure the network gateway.
- In addition to the DNS, you will need to specify the IP Address and Subnet mask.
C10: ORANGE, GREEN, ORANGE, ORANGE, [pause] = Network is transmitting data not compatible with the communication device networking protocol
Resolution:
- Wait 60 seconds. If the error does not clear, disconnect the power, wait 10 seconds, and reconnect the power.
- Check the network cable and the network port.
- If using a wireless network, make sure the wireless access point is close enough to the communication device to ensure stable reception.
C11: ORANGE, ORANGE, [pause] = MAC address access error
- Reboot the communication device:
- Unplug the device from power.
- Wait 10 seconds.
- Reconnect the power.
- Check the wireless connection:
- Make sure the wireless access point is close enough to the communication device to ensure stable reception.
- Make sure the wireless USB plug-in is attached properly to the communication device. Use the Network Setup Software to configure the device for wireless again, making sure that all settings are valid.
- Consider using the device with a wired network connection.
- If the settings failed to update, reset the device to the factory defaults.
C12: ORANGE, ORANGE, ORANGE, [pause] = IP address access error
- Reboot the communication device:
- Unplug the device from power.
- Wait 10 seconds.
- Reconnect the power.
- Check the wireless connection:
- Make sure the wireless access point is close enough to the communication device to ensure stable reception.
- Make sure the wireless USB plug-in is attached properly to the device. Use the Network Setup Software to configure the device for wireless again, making sure that all settings are valid.
- Consider using the device with a wired network connection.
- If the settings failed to update, reset the device to the factory defaults.
C13: ORANGE, GREEN, ORANGE, ORANGE, ORANGE, [pause] = Net mask access error
- If the network is set up to use DHCP, reboot the device.
- If the network does not have DHCP:
- Disconnect the USB/network cable from the franking machine.
- Download and run the Network Setup Software to verify and manually configure the Subnet mask.
- In addition to the Subnet mask, you will need to specify the IP Address, Gateway, Primary DNS, and Secondary DNS.
- If the settings failed to update, reset the device to the factory defaults.
- Check the wireless connection:
- Make sure the wireless USB plug-in is attached properly to the device.
- Use the Network Setup Software to configure the device for wireless again, making sure that all settings are valid.
- Consider using the device with a wired network connection.
- If the settings failed to update, reset the device to the factory defaults.
C14: ORANGE, GREEN, ORANGE, GREEN, ORANGE, [pause] = Interface access error
- Reboot the communication device:
- Unplug the device from power.
- Wait 10 seconds.
- Reconnect the power.
- Check the wireless connection:
- Make sure the wireless USB plug-in is attached properly to the device.
- Use the Network Setup Software to configure the device for wireless again, making sure that all settings are valid.
- Consider using the device with a wired network connection.
- If the settings failed to update, reset the device to the factory defaults.
ORANGE, GREEN, GREEN, [pause] = Web Interface Error
Disconnect the franking machine from the box when accessing the Network Setup Utility.
Flashing GREEN is a normal condition indicating that the franking machine has a functioning connection.
If you are unable to connect to the internet, ask your IT department or internet provider to check the internet settings before you contact Pitney Bowes. If you still need assistance, please contact us.
Comments
0 comments
Please sign in to leave a comment.